Mobile Public Toilet Production

There are mainly three methods for producing mobile public toilets: using water storage barrels, discarded tiles, and water storage tanks with pallets. Here are the specific introductions:

Production Using Water Storage Barrels

First, split a water storage barrel in half lengthwise with an angle grinder. Fix universal wheels at the four corners of a wooden board for mobility. Use wooden strips and self-tapping screws to secure them to the upper side of the barrel to increase height. Create an opening on the side of the water storage barrel, install sponge strips to form a door frame, and embed plastic soft boards to create raised walls. Place the upper half of the water storage barrel on top of the wooden strips as a roof and apply white waterproof paint to enhance aesthetics. Use foam strips to拼接 (assemble) discarded honeycomb wooden boards to make a simple door. Create a hole at the bottom of the barrel and install a drain pipe to form a floor drain. Drill holes on the side and bottom of the plastic barrel to connect direct fittings. Place the plastic barrel on the roof to form a small water storage device and connect it to a shower made of water pipes. Install a tee fitting below the water inlet pipe and connect a showerhead. Place a toilet and install a water tank, securing the toilet with glass glue and connecting the drain pipe to a sewage barrel. Horizontally connect a water pipe to the tee fitting on the outlet pipe and extend it to the doorway as the water inlet pipe for the sink. Drill a hole in the door and install a fitting to connect a hose.

Production of a Movable Toilet Using Discarded Tiles

First, place the toilet on a tile and use a ruler to draw a red marking line along the edge of the toilet. After moving the toilet away, use an angle grinder to cut out a rectangular tile piece slightly larger than the bottom of the toilet along the marking line. Flip the rectangular tile over and place universal wheels at each of the four corners. Use a marker to draw marking points and drill corresponding screw holes with an electric drill. Realign the universal wheels with the screw holes, insert bolts, and tighten nuts to secure them. Then, use an angle grinder to cut off the protruding bolts on the back of the tile. Place the toilet back on the tile, draw marking lines along the edge of the toilet, and mark the position of the sewage outlet at the bottom of the toilet that connects to the drainage. Insert a hose from the bottom of the tile and secure it. Apply white cement along the marking lines on the tile and place the toilet on them according to the marking lines to adhere it to the tile with the cement. After that, move the toilet with the installed base to the bathroom, install the water tank, tighten the plastic fasteners, cover the water tank lid, install the toilet seat, place the sewage hose into the drain pipe, and connect the water inlet pipe to the water tank.

Production Using Water Storage Tanks and Pallets

Fix universal wheels at each of the four corners of a plastic pallet. Place water storage tanks collected from a garbage station on the pallet. Use an angle grinder to cut along the marking line on the top of the water storage tank to remove the top surface and form an open tank. Invert another open-top water storage tank and stack it on top of the first tank, securing the outer frames of the two water storage tanks with self-tapping screws. Cut a rectangular opening with a height of 180 cm and a width of 50 cm on the outer frame of the water storage tank and cut the tank body accordingly to form a doorway. Use a hole-opening tool to create a hole on the internal floor of the water storage tank, insert an elbow from the bottom upwards, cut a section of water pipe and seal the gap with glue, cut off the excess water pipe protruding above the floor, align the toilet with the drain outlet and secure it with glue. Fix a water pipe on the wall clip and install a faucet. Secure a pipe cap with screws below the faucet, connect a water pipe to the pipe cap, and create a hole at the bottom as the outlet for the drain pipe. Apply glass glue to the pipe cap and secure a sink made of a stainless steel basin. Connect the water inlet pipe to the toilet water tank, connect the shower hose and install a shower bracket, install the toilet seat and a spray-type showerhead made of water pipes, bring a wooden board, fix hinges on the frame of the water storage tank, fix the other side of the hinges to the wooden board to form the door of the bathroom, and install a door handle on the door.